*****************************************************
ECpv2 release text
*****************************************************

*****************************************************
Version 1.00.0 based on ECpv Verion 1.86.0
*****************************************************
1- Support of Analogue IO modules EX04AIO and EX04AIS.
2- Analogue sensors supported via the Analogue IO modules.
3- Fuel level sensor support added.
4- Fuel level alarm added.
5- Support of Fuel pressure sensor readout added.
6- Support of BDSensor DCL531 added.
7- P/Q Mains reference manipulation via RRCR Analogue scheme added.
8- Load meter support added.
9- Load meter data made possible to use for control routine.
10- Command timer added.
11- Command panel interface added. 
12- Support of multiple inverter clusters via Huawei Smartloggers, Sungrow COM100E or SMA InverterManagers.
 
*****************************************************
Version 1.01.0 based on version 1.00.0
*****************************************************
1- Support of WindMeter from Soluzione Solare added.
2- Windspeed now displayed with one decimal.
3- Settings for Panel degradation, DC losses and AC losses are added to the PV generating capacity scheme.
4- SDMO APM802 support added.
5- Chint 14_36kW support added.
6- Chint SCA 18_36kW support added.
7- Sofar 80_136kW support added.

*****************************************************
Version 1.02.0 based on version 1.01.0
*****************************************************
1- Weekday added to Command timers.

*****************************************************
Version 1.02.1 based on Version 1.02.0
*****************************************************
1- Config read fail could be provoked unexpectedly.

*****************************************************
Version 1.02.2 based on Version 1.02.1
*****************************************************
1- Eventlog handling updated.

********************************
Version 1.03.0 based on version 1.02.2
********************************
1- Support of PV control selection "P ONLY" added.
2- Support of inverter acquisition when using the Sungrow COM100E protocol added.
3- Support of meteo acquisition from a PC-4 when using the Sungrow COM100E protocol added.
4- Update of SPM32/SPM33 meter handling in case of presence of PTs.
 
********************************
Version 1.04.0 based on version 1.03.0
********************************
1- Support of SGC120/121 
2- Support of SunMeter Pro WIND (with one decimal display). 
3- BOM offset added
4- DFUN DFPM93 power meter support added
5- WEG 750SIW inverter protocol added.
6- All PWMet sensors are now supported.
7- DEYE inverter protocol added.
8- Acuvim L protocol updated.

********************************
Version 1.04.1 based on version 1.04.0
********************************
1- Menu split-up.

********************************
Version 1.04.2 based on version 1.04.1
********************************
1- ABB TRIO protocol handling updated.

********************************
Version 1.05.0 based on version 1.04.2
********************************
1- EClogic alarms added. 
2- EClogic timers added. 

********************************
1.05.1 based on version 1.05.0
********************************
1- WEG protocol updated.

********************************
Version 1.06.0 based on version 1.05.1
********************************
1- Sensitivity handling of Modbus Master alarms added.

********************************
Version 1.07.0 based on version 1.06.0
********************************
1- Inverter power production deviation alarm support added.
2- Inhinitation of inverter communication alarms based on night condition and/or low POA condition support added.
3- Lettel MCX-34V support added.

*****************************************************
Version 1.07.1 based on version 1.07.0
*****************************************************
1- Modbus TCP on Power meter and IO communication updated.
2- Modbus Master sensitivity scheme for superior loggers like Smartlogger and COM100E updated.
3- EClogic Modbus Events added.
4- Change made to Acuvim L handling.

*****************************************************
Version 1.07.2 based on version 1.07.1
*****************************************************
1- Correction made to Acuvim L handling.

********************************
Version 1.07.3 based on version 1.07.2
********************************
1- Update made to handling of "Control ID/IP" readings.

********************************
Version 1.07.4 based on version 1.07.3
********************************
1- SunSpec handling updated.
2- Update made to Alarm Signal handling.

********************************
Version 1.07.5 based on version 1.07.4
********************************
1- TCP Client handling updated.

********************************
Version 1.07.6 based on version 1.07.5
********************************
1- TCP Client update made in 1.07.5 enhanced.

********************************
Version 1.08.0 based on version 1.07.6
********************************
1- Datakom D300_500_700 support added.
2- PV generating capacity is now set to 0kW in case it is night time and the generating capacity method is set to OFF.

********************************
Version 1.09.0 based on version 1.08.0
********************************
1- InteliGen_4_200 support added.
2- InteliMains_210 support added.
3- Rica RK200 and RK220 support added.

********************************
Version 1.09.1 based on version 1.09.0
********************************
1- The buttons for going to inverter data 17-32 was not taking inverter cluster into consideration
causing the page to be hidded when not supposed to.  
2- Mains readings was not shown on Overview page if it came from "PV_COMM".
3- Mains readings was not shown on Overview page if it came from "MODBUS PAGE 03".
4- DG readings was not shown on Overview page if it came from "MODBUS PAGE 03".

********************************
Version 1.09.2 based on version 1.09.1
********************************
1- Update made to reboot handling.

********************************
Version 1.10.0 based on version 1.09.2
********************************
1- SMA DataManager support added.
2- Some Mains counter elements where not saved with the correct label.

********************************
Version 1.10.1 based on version 1.10.0
********************************
1- SMA DataManager support updated.

********************************
Version 1.11.0 based on version 1.10.1
********************************
1- INVT XG support added.
2- Reactive power control added for Sofar 80-136kW handling.
3- Start/stop command added for Sofar 80-136kW inverter handling.

********************************
Version 1.11.1 based on version 1.11.0
********************************
1- SMA DataManager support updated.

********************************
Version 1.12.0 based on version 1.11.1
********************************
New features:
1- Acrel ADL3000-E support added.
2- Increased from 4 to 8 EClogic alarms.

********************************
Version 1.12.1 based on version 1.12.0
********************************
1- All "No alarm" logs generated at power up are now suppressed.
2- Load icon and busbar lines is now green in case genset or grid is connected.
3- SMA Datamanager number of decimals to use for control commands can now be set via settings.
4- Update made for Ginlong Solis.

********************************
Version 1.12.2 based on version 1.12.1
********************************
1- EClogic alarm texts handling updated.
2- Modbus Slave handling updated.
3- Modbus data for total number and number of secondary inverters present in the plant where not correct.

********************************
Version 1.12.3 based on version 1.12.2
********************************
1- NTP sync alarm is now self-acknowledging.

********************************
Version 1.12.4 based on version 1.12.3
********************************
1- Smartlogger handling updated.

********************************
Version 1.12.5 based on version 1.12.4
********************************
1- Active power for individual phases included in the Huawei power meter protocol support.

********************************
Version 1.13.0 based on version 1.12.5
********************************
1- Selection for displaying the relative or total load and grid and genset powers.

********************************
Version 1.13.1 based on version 1.13.0
********************************
1- Update made to the Carlo Gavazzi EM300 handling.
2- Update made to the Datakom D300-700 handling.

********************************
Version 1.13.2 based on version 1.13.1
********************************
1- The "Sync-SR" routine is updated.

********************************
Version 1.14.0 based on version 1.13.2
********************************
1- Support of Selec MFM384 added.
2- WEG SIW750 handling updated.

************************************************
Version 1.14.1 based on version 1.14.0
************************************************
1- Default setup for COM2 and COM3 changed.
2- Default setup for NTP changed.
3- DSE GenComm. support updated.

********************************
Version 1.15.0 based on version 1.14.1
********************************
1- Support for SAH XY-MD02 added.
2- Deye handling updated.
3- SMA DataManager added as grid power meter selection.

********************************
Version 1.16.0 based on version 1.15.0
********************************
1- Support for Cummins MCM3320 added.
2- Support for Cummins Sices MC200/MC400 added.
3- Option of using fixed CT/VT settings for SPM32 and SPM33 added.

********************************
Version 1.16.1 based on version 1.16.0
********************************
1- Grid readings via SMA DataManager updated.

********************************
Version 1.16.2 based on version 1.16.1
********************************
1- Update made to sensor handling.
2- Deye inverter handling updated.

********************************
Version 1.16.3 based on version 1.16.2
********************************
1- Clock handling updated.

********************************
Version 1.17.0 based on version 1.16.3
********************************
1- Spot price support added.
2- Solax X3-MEGA and G2G3-FORTH support added.

********************************
Version 1.18.0 based on version 1.17.0
********************************
1- Include PV energy while grid parallel in CO2 saving calculation.
2- Same cosphi option added to Mains Q CTRL. 
3- Limit option for RRCR added. 
4- Mains Reading option added to the PV "kW Origin"

********************************
Version 1.19.0 based on version 1.18.0
********************************
1- Support added for Lufft WS200 weather station

********************************
Version 1.20.0 based on version 1.19.0
********************************
1- Support added for Ingeteam 3Play inverter

********************************
Version 1.21.0 based on version 1.20.0
********************************
1- Support added for LogicsPowerAMR PYRA 300V MeteoSensor
2- Update made to inverter cluster capacity editing